Termékek
-
Dynair PS-L/INOX Backward curved blade centrifugal fans for dusty air
Construction
- Volute casing in steel sheet , protected against atmospheric agents by epoxy paint
- Aerodynamically shaped inlet cone in steel sheet, protected against atmospheric agents by epoxy paint
- Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
- For execution 1 – 9 – 12: mono-block support in cast iron with ball bearings, , designed for easy lubrication. Pulleys, belts and motor support. Belt protection guard
- Asynchronous three-phase motors according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load)
Accessories
- Condensation drain hole (TS)
- Inspection door (PI)
- Inlet counter-flange (CFA)
- Outlet counter-flange (CFP)
- Inlet protection guard (RA)
- Outlet protection guard (RP)
- Inlet flexible connector (GA)
- Outlet flexible connector (GP)
- Inlet vane control
- Outlet setting shutter
- Anti-vibration mounts
CATALOGUE
Quick ViewA termék már hozzá lett adva! View Wishlist -
Dynair PS-L/AT-INOX Backward curved blade centrifugal fans for dusty air
Construction
- Volute casing in steel sheet , protected against atmospheric agents by epoxy paint
- Aerodynamically shaped inlet cone in steel sheet, protected against atmospheric agents by epoxy paint
- Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
- For execution 1 – 9 – 12: mono-block support in cast iron with ball bearings, , designed for easy lubrication. Pulleys, belts and motor support. Belt protection guard
- Asynchronous three-phase motors according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load)
Accessories
- Condensation drain hole (TS)
- Inspection door (PI)
- Inlet counter-flange (CFA)
- Outlet counter-flange (CFP)
- Inlet protection guard (RA)
- Outlet protection guard (RP)
- Inlet flexible connector (GA)
- Outlet flexible connector (GP)
- Inlet vane control
- Outlet setting shutter
- Anti-vibration mounts
CATALOGUE
Quick ViewA termék már hozzá lett adva! View Wishlist -
Dynair PS-L Backward curved blade centrifugal fans for dusty air
Construction
- Volute casing in steel sheet, protected against atmospheric agents by epoxy paint
- Aerodynamically shaped inlet cone in steel sheet, protected against atmospheric agents by epoxy paint
- Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
- For execution 1–9–12: mono-block support in cast iron with ball bearings, designed for easy lubrication. Pulleys, belts and motor support. Belt protection guard
- Asynchronous three-phase motors according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load).
Accessories
- Condensation drain hole (TS)
- Inspection door (PI)
- Inlet counter-flange (CFA)
- Outlet counter-flange (CFP)
- Inlet protection guard (RA)
- Outlet protection guard (RP)
- Inlet flexible connector (GA)
- Outlet flexible connector (GP)
- Inlet vane control
- Outlet setting shutter
- Anti-vibration mounts
CATALOGUE
-
Dynair PS-L ATEX Backward curved blade centrifugal fans for dusty air
Construction
- Volute casing in steel sheet, protected against atmospheric agents by epoxy paint. Connection flanges ISO 6580/EUROVENT 1-2
- Aerodynamically shaped inlet cone
- Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
- Execution 4 directly coupled and executions 1-9-12 with mono-block support in cast iron with ball bearings, designed for an ideal alignment of the ball bearings and an easy lubrication
- Pulleys, belts and motor support suitable for the regulation of the belts tension. Belt protection guard according to EN12499
- Asynchronous three-phase ATEX motors for explosive atmospheres category G group II thermal class T4 protection Exd according to international standards IEC 60034, IEC 60072, IEC60079 and/or 61241, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, Class F, B3 or B5 format and ATEX certified da Notify body. Suitable to S1 service (continuous working at constant load).
Accessories
- Condensation drain hole (TS)
- Inspection door (PI)
- Inlet counter-flange (CFA)
- Outlet counter-flange (CFP)
- Inlet protection guard (RA)
- Outlet protection guard (RP)
- Inlet flexible connector (GA)
- Outlet flexible connector (GP)
- Inlet vane control
- Outlet setting shutter
- Anti-vibration mounts
CATALOGUE
-
Dynair PR-Q HT Backward curved centrifugal fans F400
Construction
- Volute casing with quadrangular frame, manufactured in galvanized steel sheet
- Single inlet, backward curved wheel with high efficiency, manufactured in galvanized steel sheet and die-cast aluminium hub
- Execution 5 (impeller directly coupled to flanged motor), rotation RD
- Double speed asynchronous three-phase motor manufactured according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F. Double speed by delta/star switching. Electric supply: 400V / 50 HZ three phase
Accessories
- Inlet/outlet flexible connectors
- Inlet and outlet protection guard manufactured according to UNI 12499 norm and protected against atmospheric agents
- Inlet/outlet counterflange
- Antivibration supports
- Self transformer or inverters speed controllers
CATALOGUE
Quick ViewA termék már hozzá lett adva! View Wishlist -
Dynair PR-Q AT Backward curved blade centrifugal fans for clean air or slightly dusty air with t from 100 to 200°C
Construction
- Volute casing with quadrangular frame, manufactured in galvanized steel sheet and protected against atmospheric agents with epoxy finish
- Single inlet, backward curved wheel with high efficiency, manufactured in galvanized steel sheet and die-cast aluminium hub
- Execution 5 (impeller directly coupled to fl anged motor), rotation RD
- Asynchronous three-phase or single-phase motors according to international standards IEC 60034, IEC 60072, EMC 2014/30/CE, LVD 2014/35/UE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load)
Accessories
- Inlet and outlet protection guard manufactured according to UNI 12499 norm and protected against atmospheric agents
- Inlet/outlet flexible connectors
- Antivibration supports
- Inlet/outlet counterflange
- Self transformer or inverters speed controllers
CATALOGUE
ACCESSORIES
-
Dynair PR-Q AT Backward curved blade centrifugal fans for clean air or slightly dusty air with t from 100 to 200°C
Construction
- Volute casing with quadrangular frame, manufactured in galvanized steel sheet and protected against atmospheric agents with epoxy finish
- Single inlet, backward curved wheel with high efficiency, manufactured in galvanized steel sheet and die-cast aluminium hub
- Execution 5 (impeller directly coupled to fl anged motor), rotation RD
- Asynchronous three-phase or single-phase motors according to international standards IEC 60034, IEC 60072, EMC 2014/30/CE, LVD 2014/35/UE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load)
Accessories
- Inlet and outlet protection guard manufactured according to UNI 12499 norm and protected against atmospheric agents
- Inlet/outlet flexible connectors
- Antivibration supports
- Inlet/outlet counterflange
- Self transformer or inverters speed controllers
CATALOGUE
ACCESSORIES
-
Dynair PR-L/INOX Backward curved blade centrifugal fans for clean or slightly dusty air
Construction
- Volute casing in steel sheet, protected against atmospheric agents by epoxy paint
- Aerodynamically shaped inlet cone in steel sheet, protected against atmospheric agents by epoxy paint
- Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
- For execution 1 – 9 – 12: mono-block support in cast iron with ball bearings, designed for easy lubrication. Pulleys, belts and motor support. Belt protection guard
- Asynchronous three-phase motors according to international standards IEC 600034, IEC 60072, EMC 2004/108/CE, LVD 2006/95/CE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load).
Accessories
- Condensation drain hole (TS)
- Inspection door (PI)
- Inlet counter-flange (CFA)
- Outlet counter-flange (CFP)
- Inlet protection guard (RA)
- Outlet protection guard (RP)
- Inlet flexible connector (GA)
- Outlet flexible connector (GP)
- Inlet vane control
- Outlet setting shutter
- Anti-vibration mounts
CATALOGUE
Quick ViewA termék már hozzá lett adva! View Wishlist -
Dynair PR-L Backward curved blade centrifugal fans for clean or slightly dusty air
Construction
- Volute casing in steel sheet , protected against atmospheric agents by epoxy paint
- Aerodynamically shaped inlet cone in steel sheet, protected against atmospheric agents by epoxy paint
- Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
- For execution 1 – 9 – 12: mono-block support in cast iron with ball bearings, , designed for easy lubrication. Pulleys, belts and motor support. Belt protection guard
- Asynchronous three-phase motors according to international standards IEC 600034, IEC 60072, EMC 2004/108/CE, LVD 2006/95/CE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load)
Accessories
- Condensation drain hole (TS)
- Inspection door (PI)
- Inlet counter-flange (CFA)
- Outlet counter-flange (CFP)
- Inlet protection guard (RA)
- Outlet protection guard (RP)
- Inlet flexible connector (GA)
- Outlet flexible connector (GP)
- Inlet vane control
- Outlet setting shutter
- Anti-vibration mounts
CATALOGUE
-
Dynair PR-L ATEX Backward curved blade centrifugal fans for clean or slightly dusty air
Construction
- Volute casing in steel sheet , protected against atmospheric agents by epoxy paint. Connection flanges ISO 6580/EUROVENT 1-2.
- Aerodynamically shaped inlet cone
- Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
- Execution 4 directly coupled and executions 1 – 9 – 12 with mono-block support in cast iron with ball bearings, designed for an ideal alignment of the ball bearings and an easy lubrication. Pulleys, belts and motor support suitable for the regulation of the belts tension. Belt protection guard according to EN12499.
- Asynchronous three-phase ATEX for explosive atmospheres category G group II thermal class T4 protection Exd motors according to international standards IEC 60034, IEC 60072, IEC60079 and/or 61241, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, Class F, B3 or B5 format and ATEX certified da Notify body. Suitable to S1 service (continuous working at constant load).
Accessories
- Condensation drain hole (TS)
- Inspection door (PI)
- Inlet counter-flange (CFA)
- Outlet counter-flange (CFP)
- Inlet protection guard (RA)
- Outlet protection guard (RP)
- Inlet flexible connector (GA)
- Outlet flexible connector (GP)
- Anti-vibration mounts
CATALOGUE
-
Dynair PR-AC Centrifugal fans in plastic material
Construction
- Volute in polyethylene (PE)
- Single inlet impeller, in Polypropylene (PP), with backward curved blades and aluminium hub (protected from the fluid)
- Motor support in epoxy painted steel sheet
- Asynchronous three-phase or single-phase motors according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F, B3 or B5 shape. Suitable to a S1 service (continuous working to constant load)
Accessories
- Inlet protection guard according to UNI 10615
- Anti-vibration joint in PVC for inlet and outlet sides
- Gravity shutter
- Manual setting shutter
CATALOGUE
-
DYNAIR PR-AC ATEX Centrifugal fans in plastic material
Construction
- Volute in polyethylene
- Single inlet impeller, in Polypropylene, with backward curved blades and aluminium hub (protected from the fluid)
- Motor support in epoxy painted steel sheet
- Asynchronous three-phase or single-phase ATEX motors for explosive atmospheres category G group II thermal class T4 protection Exd according to international standards IEC 600034, IEC 60072, EMC 2004/108/CE, LVD 2006/95/CE, CE marked, IP 55, class F, B3 or B5 shape. Suitable to a S1 service (continuous working to constant load)
Accessories
- Inlet protection guard according to UNI 10615
- Anti-vibration joint in PVC for inlet and outlet sides
- Gravity shutter
- Manual setting shutter
CATALOGUE
-
Dynair PQ-L/INOX Backward curved blade centrifugal fans for dusty air
Construction
- Volute casing in steel sheet, protected against atmospheric agents by epoxy paint
- Aerodynamically shaped inlet cone in steel sheet, protected against atmospheric agents by epoxy paint
- Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
- For execution 1 – 9 – 12: mono-block support in cast iron with ball bearings, , designed for easy lubrication. Pulleys, belts and motor support. Belt protection guard
- Asynchronous three-phase motors according to international standards IEC 600034, IEC 60072, EMC 2004/108/CE, LVD 2006/95/CE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load)
Accessories
- Condensation drain hole (TS)
- Inspection door (PI)
- Inlet counter-flange (CFA)
- Outlet counter-flange (CFP)
- Inlet protection guard (RA)
- Outlet protection guard (RP)
- Inlet flexible connector (GA)
- Outlet flexible connector (GP)
- Inlet vane control
- Outlet setting shutter
- Anti-vibration mounts
CATALOGUE
-
Dynair PQ-L Backward curved blade centrifugal fans for dusty air
Construction
- Volute casing in steel sheet, protected against atmospheric agents by epoxy paint
- Aerodynamically shaped inlet cone in steel sheet, protected against atmospheric agents by epoxy paint
- Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
- For execution 1–9–12: mono-block support in cast iron with ball bearings, designed for easy lubrication. Pulleys, belts and motor support. Belt protection guard.
- Asynchronous three-phase motors according to international standards IEC 600034, IEC 60072, EMC 2004/108/CE, LVD 2006/95/CE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load).
Accessories
- Condensation drain hole (TS)
- Inspection door (PI)
- Inlet counter-flange (CFA)
- Outlet counter-flange (CFP)
- Inlet protection guard (RA)
- Outlet protection guard (RP)
- Inlet flexible connector (GA)
- Outlet flexible connector (GP)
- Inlet vane control
- Outlet setting shutter
- Anti-vibration mounts
CATALOGUE
-
Dynair PQ-L ATEX Backward curved blade centrifugal fans
Construction
- Volute casing in steel sheet, protected against atmospheric agents by epoxy paint. Connection flanges ISO 6580/EUROVENT 1-2
- Single inlet backward curved wheel with high efficiency, manufactured in steel sheet and epoxy painted. For high rotational speed, versions in class 3 are foreseen
- Aerodynamically shaped inlet cone
- Execution 4 directly coupled and executions 1-9-12 with mono-block support in cast iron with ball bearings, designed for easy lubrication. Pulleys, belts and motor support. Belt protection guard according to EN12499
Accessories
- Condensation drain hole (TS)
- Inspection door (PI)
- Inlet counter-flange (CFA)
- Outlet counter-flange (CFP)
- Inlet protection guard (RA)
- Outlet protection guard (RP)
- Inlet flexible connector (GA)
- Outlet flexible connector (GP)
- Inlet vane control
- Outlet setting shutter
- Anti-vibration mounts
CATALOGUE
-
Dynair MULTIBOX Centralized single flow extract ventilation
Construction
- Casing in galvanised steel sheet.
- Backward blade impeller for high efficiency and low noise level.
- Easy access to motor and impeller for inspection.
- Compliance with EN 60335-2-80, B.T. 2014/35/UE, EMC 2014/30/UE
- IPX4
Accessories
- RLS 1 WR Remote control for the manual selection of the ventilation level (min/Intermediate/high). Suitable for Microbox EC.
- RLS 3V Remote control for the manual selection of the ventilation level (min/Intermediate/high) and On/Off switch. Suitable for Microvox 3V AC.
CATALOGUE
-
Dynair Mini-Box Slim-line acoustic cabinet fans
Construction
• Casing in galvanized steel sheet, lined with acoustic insulation (thickness 10 mm).
• Single-phase electric motor, IP44, class F, with thermal protection, suitable for speed control.
• Fitting bracket
• Backward curved impeller with high effi ciency and low noise level.
• Outer terminal box IP55.Accessories
• Electric duct heaters BE.
• Backdraught shutters.
• Duct clamps.
• Protection guardsCATALOGUE
ACCESSORIES
-
Dynair MICROBOX Centralized single flow extract ventilation
Construction
- Casing in galvanised steel sheet inside lined with acoustic insulation.
- Backward blade impeller for high efficiency and low noise level.
- Wall/ceiling fixing kit for an easy and quick installation (Maico Italia patent).
- Easy access to motor and impeller for inspection.
- Supplied with plastic sealing rings for the spigots.
- Compliance with EN 60335-2-80, B.T. 2014/35/UE, EMC 2014/30/UE
- IPX4
Accessories
- RLS 1 WR Remote control for the manual selection of the ventilation level (min / Intermediate / high). Suitable for Microbox EC.
- RLS 3V Remote control for the manual selection of the ventilation level (min / Intermediate / high) and On/Off switch. Suitable for Microvox 3V AC.
CATALOGUE
-
Dynair JET FANS CC JD LP Axial impulse fans – Low profile shape
Construction
- Silencers in galvanized steel sheet inside lined with high performance acoustic insulation material
- Deflector on outlet side for optimum air discharge and air cleaning of all layers. Supplied as standard
- Protection guard on inlet side
- Fixing brackets in galvanized steel sheet for ceiling (or wall) installation. Supplied as standard and pre-assembled
- Octagonal shaped silencers
- Housing in electrolytically galvanized steel sheet
- Hub impeller and airfoil profile blades made in aluminium. Balanced according to ISO 1940 G.6.3. Variable pitch angle in still position
- Terminal box IP54, resistant to high temperature and supplied as standard
- Asynchronous three-phase motors 380-420V 50Hz according to international standards IEC 60034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE. Motors suitable for DOL (Direct On Line) start. CE marked. Protection IP55, class F or H. Execution 4 (with impeller directly coupled to motor with feet).
CATALOGUE
-
Dynair JET FANS CC JD Axial impulse fans
Construction
- Silencers in galvanized steel sheet inside lined with high performance acoustic insulation material
- Deflector on outlet side for optimum air discharge and air cleaning of all layers. Supplied as standard
- Protection guard on inlet side
- Fixing brackets in galvanized steel sheet for ceiling (or wall) installation. Supplied as standard and pre-assembled
- Silencers are fi tted at both ends with an especially designed smooth bell shape to improve air performance and reduce losses and sound level
- Housing in electrolytically galvanized steel sheet
- Hub impeller and airfoil profi le blades made in aluminium. Balanced according to ISO 1940. Variable pitch angle in still position
- Terminal box IP54, resistant to high temperature and supplied as standard.
MOTOR
Asynchronous three-phase motors 380-420V 50 Hz according to international standards IEC 60034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE.
Motors suitable for DOL (Direct On Line) start. CE marked. Protection IP55, class F or H.
Execution 4 (with impeller directly coupled to motor with feet).CATALOGUE
-
Dynair Inverter and Line filter
VSD – Variable Speed Drive.
- SPWM Control
- Integrated EMI filter
- Settable operation functions
- Interface MODBAS RS485.
- Upon request DeviceNet, Profi bus, Lon Works, CANopen protocols
- Wall installation, optional DIN bar
VFD “EL”: Keypad with incorporated fixed potentiometer.
VFD “E”: Integrated PLC. Keypad with removable potentiometer, ideal for multiple installations with a unique and remote-manageable programmation (a cable of 5 mt max. length is available upon request). Mounting port for extension card available.KATALOG
Quick ViewA termék már hozzá lett adva! View Wishlist -
Dynair FCV Single speed centrifugal roof fans – Vertical discharge
Construction
- Base frame in galvanized steel sheet
- Protection guard in drawn steel rod protected against the atmospheric agents, manufactured according to UNI 10615:1997
- Backward curved wheel in galvanized steel sheet, with high efficiency and low noise level, statically and dynamically balanced according ISO 1940
- Asynchronous three-phase motor or single-phase motor manufactured according to international standards IEC 600034, IEC 60072, EMC 2004/108/CE, LVD 2006/95/ CE, CE marked, IP 55, class F
- Upper cover in ABS, with appropriate slots for motor cooling
- Outer deflector in ABS
Accessories
- Backdraught gravity shutter (TS)
- Silencer (GR)
- Support base for wawed roof coverings (BA)
- Inlet Protection Guard (RA)
- Service switch
- Support base/Silenced reduction (PB)
CATALOGUE
ACCESSORIES
-
Dynair FCV 2V Double speed centrifugal roof fans – Vertical discharge
Construction
- Base frame in galvanized steel sheet
- Protection guard in drawn steel rod protected against the atmospheric agents, manufactured according to UNI 10615:1997
- Backward curved wheel in galvanized steel sheet, with high efficiency and low noise level, statically and dynamically balanced according ISO 1940
- Asynchronous three-phase motor or single-phase motor manufactured according to international standards IEC 600034, IEC 60072, EMC 2004/108/CE, LVD 2006/95/ CE, CE marked, IP 55, class F.
- Upper cover in ABS, with appropriate slots for motor cooling
- Outer deflector in ABS
Accessories
- Backdraught gravity shutter (TS)
- Silencer (GR)
- Support base for wawed roof coverings (BA)
- Inlet Protection Guard (RA)
- Service switch
- Support base/Silenced reduction (PB)
CATALOGUE
ACCESSORIES
-
Dynair FC-HT Centrifugal roof fans F400
Construction
- Base frame in galvanized steel sheet
- Protection guard in drawn steel rod protected against the atmospheric agents
- Backward curved wheel in galvanized steel sheet, with high effi ciency and low noise level, statically and dynamically balanced according ISO 1940
- Upper cover in ABS, with appropriate slots for motor cooling (collapsing controlled cowl in case of fire)
- Double speed asynchronous three-phase motor manufactured according to international standards IEC 60034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F. Electric supply: 400V / 50 HZ three phase
Accessories
- Counter-base to be walled-up (CB)
- Inlet side grid (CCr)
CATALOGUE
-
Dynair FC Single speed centrifugal roof fans – Horizontal discharge
Construction
- Base frame in galvanized steel sheet.
- Protection guard in drawn steel rod protected against the atmospheric agents, manufactured according to UNI 10615:1997.
- Backward curved wheel in galvanized steel sheet, with high efficiency and low noise level, statically and dynamically balanced according ISO 1940.
- Asynchronous three-phase motor or single-phase motor manufactured according to international standards IEC 600034, IEC 60072, EMC 2004/108/CE, LVD 2006/95/ CE, CE marked, IP 55, class F.
- Upper cover in ABS, with appropriate slots for motor cooling.
- Outer deflector (FCV) in ABS
Accessories
- Backdraught gravity shutter (TS)
- Silencer (GR)
- Support base for wawed roof coverings (BA)
- Inlet Protection Guard (RA)
- Service switch
- Support base/Silenced reduction (PB)
CATALOGUE
ACCESSORIES
Quick ViewA termék már hozzá lett adva! View Wishlist -
Dynair FC AT – FC 2V AT Single or dpouble speed centrifugal roof fans for air temperature up to 200°C
CONSTRUCTION
- Base frame in galvanized steel sheet
- Protection guard in drawn steel rod protected against the atmospheric agents, manufactured according to UNI EN 12499
- Backward curved wheel in galvanized steel sheet, with high efficiency and low noise level, statically and dynamically balanced according ISO 1940
- Upper cover in aluminium, with appropriate slots for motor cooling
- Asynchronous three-phase motor or singlephase motor manufactured according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked,
IP 55, class F
ACCESSORIES
- Backdraught gravity shutter (TS)
- Silencer (GR)
- Counterbase (CB)
- Support base for wawed roof coverings (BA)
- Inlet Protection Guard (RA)
- Service switch
- Support base/Silenced reduction (PB)
- Flat protection guard (CCr)
CATALOGUE
-
Dynair FC 2V Double speed centrifugal roof fans – Horinzontal discharge
Construction
- Base frame in galvanized steel sheet
- Protection guard in drawn steel rod protected against the atmospheric agents, manufactured according to UNI 10615:1997
- Backward curved wheel in galvanized steel sheet, with high efficiency and low noise level, statically and dynamically balanced according ISO 1940
- Asynchronous and double polarity three-phase motor manufactured according to international standards IEC 60034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP55 Class F.
- Upper cover in techno-polymer, with appropriate slots for motor cooling
- Outer deflector in techno-polymer.
Accessories
- Backdraught gravity shutter (TS)
- Silencers (GR)
- Counterbase (CB)
- Support base for wawed roof coverings (BA)
- Inlet side Guard (RA)
- Service switch
- Self transformer speed regulator
- Delta/start switch
- Support base/Silenced reduction (PB)
CATALOGUE
ACCESSORIES
Quick ViewA termék már hozzá lett adva! View Wishlist -
Dynair F Radial blade centrifugal fans in aluminium
Construction
- Volute casing in die cast aluminium, protected against atmospheric agent by epoxy paint. Support feet are integral part of the casing
- Single inlet, open blade, radial impeller in die cast aluminium
- Execution 5 (with impeller directly coupled to flanged motor)
- Fixed orientation RD 270°
- Asynchronous three-phase or single-phase motors according to international standards IEC 600034, IEC 60072, EMC 2014/34/UE, LVD 2014/35/UE, CE marked, IP 55, class F, suitable to S1 service (continuous working at constant load).
Accessories
- Inlet protection guard manufactured according to UNI 12499 norm and protected against the atmospheric agents.
CATALOGUE
-
Dynair ERM-EX Enhanced safety mixed flow fans
The ERM-EX fans are the only mixed fl ow in line series in increased safety execution “EExe“ available on the market.
The particular construction allows the installation in hazardous environment as: battery rooms, dyeing-plants, garages, etc.
Suitable to convey clean air with working temperature from -20°C to 50°C.
The ERM-EX are not suitable for regulation.Accessories
- Reduction
- Protection guard
- Fixing clamps
CATALOGUE
-
Dynair DIC-INOX Centrifugal fans in stainless steel
Construction
- Volute in stainless steel AISI304 sheet
- Single inlet forward bladed impeller (sirocco), in stainless steel AISI304
- Execution 5 (with impeller directly coupled to flanged motor)
- Standard orientation LG270°
- Motorizations: asynchronous three-phase or single-phase motors according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F, B35 shape. DIC-INOX 100 T and M with motor shape B14, IP44, class B.
Accessories
- Inlet and outlet protection guard according to UNI 12499 norm
- Motor support in steel sheet protected against atmospheric agents by epoxy paint
CATALOGUE
ACCESSORIES
-
Dynair DIC-ATEX – DIC-INOX-ATEX Forward curved blade centrifugal fans
Construction
- Volute casing in steel sheet, protected against atmospheric agents by epoxy paint or in stainless steel AISI304 sheet
- Single inlet, single gauge, forward curved impeller (sirocco type), in galvanized steel sheet or in stainless steel AISI304
- Steel sheet inlet with epoxy finish or inox inlet on models IIB. Brass inlet on models with execution IIC
- Execution 5 (with impeller directly coupled to flanged motor)
- Motor separated from the conveyed airflow
- Standard orientation LG270°
- Inlet connector supplied (disassembled)
- DIC-ATX and DIC-ATX INOX asynchronous three- phase motors or single-phase according to international standards IEC 60034, IEC 60072, IEC 60079 and/or IEC61241, EMC 2004/108/ CE, LVD 2006/95/CE, with Atex certification for explosive atmospheres category G group II thermal class T4 protection Exd, CE marked, IP55, class F, B35 shape. Suitable to S1 service (continuous working at constant load)
Accessories
- Motor support in steel or steel sheet
- Inlet and outlet protection guard manufactured according to UNI 12499 norm and protected against the atmospheric agents
CATALOGUE
-
Dynair DIC Forward curved blade centrifugal fans
Construction
- Volute casing in steel sheet, protected againstatmospheric agents by epoxy paint
- Single inlet, single width, forward curved impeller (sirocco type), in galvanized steel sheet
- Execution 5 (with impeller directly coupled to flanged motor)
- Standard orientation LG 270°
- Motorization: Asynchronous three-phase or single-phase motors according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F, B35 shape. DIC 100 T and M with motor shape B14, IP44, class B. All motors suitable to S1 service (continuous working at constant load).
Accessories
- Inlet and outlet protection guard according to UNI 10615 rules and protected against atmospheric agents
- Motor support in steel sheet epoxy painted.
CATALOGUE
ACCESSORIES
Quick ViewA termék már hozzá lett adva! View Wishlist -
Dynair DIC AT Forward curved blade centrifugal fans for air temperature up to +150°C
Construction
- Volute casing in steel sheet, protected against atmospheric agents by epoxy paint
- Single inlet, single width forward curved impeller (sirocco type), in galvanized steel sheet
- Execution 5 (with impeller directly coupled to flanged motor)
- Standard orientation LG270°
- Asynchronous three-phase or single-phase motors according to international standards IEC 600034, IEC 60072, EMC 2014/30/UE, LVD 2014/35/UE, CE marked, IP 55, class F, B35 shape. DIC 100 T and M with motor shape B14, IP44, class B.
Accessories
- Inlet and outlet protection guard according to UNI 12499 rules and protected against atmospheric agents
- Motor support in steel sheet epoxy painted.
CATALOGUE
-
Dynair DA-T Direct drive double inlet fans without motor
The fans of the DA-T series are suitable in plants of ventilation and air conditioning, filtering and heating. They can only handle clean air with temperature range from -20°C to +80°C and to work they require a containing structure (plenum).
The fans must be used within the limits shown in the relevant table.They can only handle clean air up to the maximum temperature of 40°C and to work they require a containing structure (plenum). The fans must be used within the limits shown in the relevant table.
Upon request:
- “CUBIK” version.
CATALOGUE
ACCESSORIES
-
Dynair DA Direct drive double inlet fans
Construction
- Volute in galvanized steel sheet
- Direct drive double inlet forward curved wheel
- Single-phase and three-phase motor (only 12/9 and 12/12), IP20, class F. Thermal protection in single-phase versions. Particularly suitable for speed regulation (using the suitable speed regulators shown in this catalogue)
Accessories
- Outlet flange
- Fixing feet
CATALOGUE
ACCESSORIES
-
Dynair CCZ Compact and high efficiency ducted axial fans
Construction
- Short casing in steel sheet, with fixing flanges manufactured according to UNI ISO 6580-EUROVENT standard. Protected against atmospheric agents by epoxy paint
- High quality aerofoil profiled impellers in mineral fibres reinforced technopolymer (310 to 400) and diecast aluminum alloy (450 to 560). Blades are directly fixed to the motor external rotor
- Execution 5 (with impeller directly coupled to the motor) and airflow from motor to impeller
- External rotor motors with built-in thermal protection, double speed three-phase and single- phase, speed adjustable. All motors with mounted connection box
Accessories
- Flat protection guard (CCr)
- Flexible connectors (CCga)
- Support feet (CCst)
- Inlet/outlet bell mouth (CCbo)
- Silencers, with and without pod, in three lengths (CCsa and CCsb)
- Counter flange (Ccf)
- Counter flange with collar (CCfc)
- Anti-vibration mounts.
CATALOGUE
ACCESSORIES
